Skip to content
PDF

Siemens SIMATIC IPC427E

!Siemens SIMATIC IPC427E

The SIMATIC IPC427E is an embedded IPC with 6th generation Intel Core-i processors that can be used for control, data collection, or communication tasks at the machine or process level. It offers low mounting depth and different mounting possibilities, with all interfaces on one side for easy integration in existing plants.

For more information refer to the information materials provided by the manufacturer:

Device specifications

The table below contains the key specifications of the specific hardware model that has been certified for Nerve usage. Use the article number listed here when ordering the device from the manufacturer only. Note that other device variants are not supported as Nerve Devices.

If required, contact sales@tttech-industrial.com for help with ordering Nerve Devices.

Item Description
Article number 6AG4141-5BC00-0GA8 /SIMATIC IPC427
CPU Intel Core i5-6442EQ
Cores 4
RAM 16 GB
Storage 480 GB SATA SSD
TPM TPM 2.0 included
Interfaces
  • 3x GB LAN
  • 4x USB 3.0
  • 2x DisplayPort

Setting up the device for Nerve usage

Requirements for the instructions below:

  • a monitor with a DisplayPort input
  • a keyboard
  • a USB drive formatted to FAT32

Refer to the user manual of the manufacturer to set up the hardware. Connect a keyboard and a monitor to the device and make sure that the device is ready to be powered on. Also, prepare a USB drive in case the BIOS version of the device needs to be updated.

BIOS update

To avoid possible issues and complications, the BIOS version on the SIMATIC IPC427E needs to be version 12 or later. Refer to the user manual of the manufacturer for information on how to update the BIOS version.

Required BIOS settings for Nerve

Certain BIOS settings need to be changed to ensure the desired performance of the Nerve system.

  1. Power on the device.
  2. Press Esc while the device is booting to enter the BIOS menu.
  3. Change the following settings:

    Path Setting
    Advanced > System Agent (SA) Configuration > VT-d Enabled
    Advanced > Active Management Technology Support > Intel AMT Configuration Screens Disabled
    Advanced > Memory Configuration > Max TOLUD 2 GB
    Power > CPU Configuration > Intel (VMX) Virtualization Technology Enabled
    Power > Power & Performance > CPU - Power Management Control > CPU Power Level Standard
    Power > Power & Performance > CPU - Power Management Control > Intel (R) SpeedStep(tm) Disabled
    Power > Power & Performance > CPU - Power Management Control > Intel (R) Speed Shift Technology Disabled
    Power > Power & Performance > CPU - Power Management Control > C states Disabled
    Boot > Boot Type Dual Boot Type
    Boot > Add Boot Options Auto
    Boot > USB Boot Enabled
    Boot > EFI Device First Enabled
  4. Save the changes and exit BIOS.

Installing Nerve

Requirements for installing Nerve on the device:

  • a monitor with a DisplayPort input
  • a keyboard
  • a USB drive
  • the Nerve_Blue_USB-installer_2.4.1_for_siemens-simatic-ipc427e.img.tar.gz which can be downloaded from the Nerve Software Center
  • a tool for creating bootable USB drives like Rufus on Windows

In addition, a workstation is required to prepare the bootable USB drive. Connect the monitor and the keyboard to the SIMATIC IPC427E.

Before beginning with the installation, make sure that the device will boot from the USB drive. Press Esc when the device is booting to enter BIOS and change the boot device settings.

On Windows

  1. Download the Nerve_Blue_USB-installer_2.4.1_for_siemens-simatic-ipc427e.img.tar.gz from the Nerve Software Center to a workstation.
  2. Extract the Nerve_Blue_USB-installer_2.4.1_for_siemens-simatic-ipc427e.img.tar.gz file to retrieve the Nerve_Blue_USB-installer_2.4.1_for_siemens-simatic-ipc427e.img. Depending on the program used, the file might need to be extracted more than once.
  3. Transfer the extracted Nerve_Blue_USB-installer_2.4.1_for_siemens-simatic-ipc427e.img file to the USB drive using Rufus.
  4. Plug the USB drive into a USB port of the Nerve Device.
  5. Make sure that the device will boot from the USB drive and power on the device.

The setup will start automatically and take a few minutes to complete. Select OK when the installation is complete and remove the USB drive. The device will reboot and reach a log in screen, asking for host access log in credentials. Make sure that the device will boot from the hard disk before rebooting the device.

On Linux

  1. Download the Nerve_Blue_USB-installer_2.4.1_for_siemens-simatic-ipc427e.img.tar.gz file from the Nerve Software Center.
  2. Enter the following commands to extract the Nerve_Blue_USB-installer_2.4.1_for_siemens-simatic-ipc427e.img.tar.gz file and transfer the extracted file to the USB drive:

    tar xf Nerve_Blue_USB-installer_2.4.1_for_siemens-simatic-ipc427e.img.tar.gz
    sudo dd if=Nerve_Blue_USB-installer_2.4.1_for_siemens-simatic-ipc427e.img bs=4M of=/dev/sd<drivename> status=progress
    sync
    

    Note

    Make sure to replace <drivename> with the system name of the USB drive.

  3. Plug the USB drive into a USB port of the Nerve Device.

  4. Make sure that the device will boot from the USB drive and power on the device.

The setup will start automatically and take a few minutes to complete. Select OK when the installation is complete and remove the USB drive. The device will reboot and reach a log in screen, asking for host access log in credentials. Make sure that the device will boot from the hard disk before rebooting the device.

Activating the Nerve license

After the installation, the product license needs to be activated so that Nerve can be used on the device. Connect a workstation to port X1 P1 and configure the network adapter of the workstation. The IP address has to be in the range from 172.20.2.5 to 172.20.2.254 with a 255.255.255.0 subnet mask.

Access the Local UI at http://172.20.2.1:3333/ and refer to License activation in the user guide for more information.

Accessing the Local UI and registering the device

With the license activated, the node needs to be registered for use in the Management System through the Local UI. To access the Local UI, first connect a workstation to port X1 P1 and configure the network adapter of the workstation. The IP address has to be in the range from 172.20.2.5 to 172.20.2.254 with a 255.255.255.0 subnet mask. The credentials for the Local UI found in the customer profile are also required.

  1. Follow this link to connect to the Local UI: http://172.20.2.1:3333/
  2. Log in with the credentials from the customer profile.

    !Local UI Login

Continue with Node configuration for information on how to start registering the device in the Management System.

Physical ports and network interfaces

Below is a depiction of the node internal networking adapted to the SIMATIC IPC427E hardware. Refer to Node internal networking for more information. The table offers a quick overview of the network interfaces that can be reached through the physical ports of the SIMATIC IPC427E.

Physical port Network name
X1 P1 mgmt
X2 P1 wan
X3 P1 io0

!SIMATIC IPC427E Networking