Supermicro SuperServer E100-9AP-IA

With an excellent price/performance ratio, the Supermicro Superserver devices offer a compact design with good connectivity, allowing optimal Nerve performance. The SuperServer E100-9AP-IA is a compact, Intel Atom class embedded IPC with many connection possibilities.

For more information refer to the information materials provided by the manufacturer:

• Product page
• User manual

Device specifications

The table below contains the key specifications of the specific hardware model that has been certified for Nerve usage. Use the article number listed here when ordering the device from the manufacturer only. Note that other device variants are not supported as Nerve Devices.

If required, contact sales@tttech-industrial.com for help with ordering Nerve Devices.

Setting up the device for Nerve usage

Requirements for the instructions below:

Refer to the user manual of the manufacturer to set up the hardware. Connect a keyboard and a monitor to the device and make sure that the device is ready to be powered on. Also, prepare a USB drive in case the BIOS version of the device needs to be updated.

BIOS update

To avoid possible issues and complications, the BIOS version on the SuperServer E100-9AP-IA needs to be version 1.3 or later and Setup Utility needs to be V2.18.1263 or later. Refer to the user manual of the manufacturer for information on how to update the BIOS version.

Required BIOS settings for Nerve

Certain BIOS settings need to be changed to ensure the desired performance of the Nerve system.

1. Power on the device.
2. Press Del while the device is booting to enter the BIOS menu.

3. Change the following settings:

   Path	Setting
   Advanced > CPU Configuration > Intel Virtualization Technology	Enabled
   Advanced > Chipset Configuration > VT-d	Enabled
   Advanced > CPU Configuration > Active Processor Cores	Enabled
   Advanced > ACPI Settings > ACPI Sleep State	Suspend Disabled

4. Save the changes and exit BIOS.

Installing Nerve

Requirements for installing Nerve on the device:

In addition, a workstation is required to prepare the bootable USB drive. Connect the monitor and the keyboard to the SuperServer E100-9AP-IA.

Before beginning with the installation, make sure that the device will boot from the USB drive. Press Del when the device is booting to enter BIOS and change the boot device settings.

On Windows

1. Download the Nerve_Blue_USB-installer_2.3.1_for_supermicro-superserver-e100-9ap-ia.img.tar.gz from the Nerve Software Center to a workstation.
2. Extract the Nerve_Blue_USB-installer_2.3.1_for_supermicro-superserver-e100-9ap-ia.img.tar.gz file to retrieve the Nerve_Blue_USB-installer_2.3.1_for_supermicro-superserver-e100-9ap-ia.img. Depending on the program used, the file might need to be extracted more than once.
3. Transfer the extracted Nerve_Blue_USB-installer_2.3.1_for_supermicro-superserver-e100-9ap-ia.img file to the USB drive using Rufus.
4. Plug the USB drive into a USB port of the Nerve Device.
5. Make sure that the device will boot from the USB drive and power on the device.

The setup will start automatically and take a few minutes to complete. Select OK when the installation is complete and remove the USB drive. The device will reboot and reach a log in screen, asking for host access log in credentials. Make sure that the device will boot from the hard disk before rebooting the device.

On Linux

1. Download the Nerve_Blue_USB-installer_2.3.1_for_supermicro-superserver-e100-9ap-ia.img.tar.gz file from the Nerve Software Center.

2. Enter the following commands to extract the Nerve_Blue_USB-installer_2.3.1_for_supermicro-superserver-e100-9ap-ia.img.tar.gz file and transfer the extracted file to the USB drive:

   tar xf Nerve_Blue_USB-installer_2.3.1_for_supermicro-superserver-e100-9ap-ia.img.tar.gz
   sudo dd if=Nerve_Blue_USB-installer_2.3.1_for_supermicro-superserver-e100-9ap-ia.img bs=4M of=/dev/sd<drivename> status=progress
   sync
   

   Note

   Make sure to replace <drivename> with the system name of the USB drive.

3. Plug the USB drive into a USB port of the Nerve Device.

4. Make sure that the device will boot from the USB drive and power on the device.

The setup will start automatically and take a few minutes to complete. Select OK when the installation is complete and remove the USB drive. The device will reboot and reach a log in screen, asking for host access log in credentials. Make sure that the device will boot from the hard disk before rebooting the device.

Finding out the IP address of the device

Due to the limited availability of ethernet ports, Nerve does not offer a designated port and interface for host access and management purposes on the Supermicro SuperServer E100-9AP-IA. The IP address of the wan interface that is mapped to physical port LAN1 is required to start using Nerve. Depending on the network access the node has, this needs to be done differently.

The node has network access

If the node has network access, an IP address will be assigned to the wan interface by a DHCP server. Follow the instructions below to find out the IP address of the wan interface.

1. Connect a keyboard and a monitor to the device.
2. Power up the device once Nerve is installed.
3. Enter the login credentials for host access once the system asks for host login. The login credentials can be found in the customer profile.

4. Enter the following command to display the IP address of the wan interface:

   ip a s wan
   

The IP address is displayed next to inet in the output the system gives. This IP address is required to access the Local UI in the instructions below.

The node does not have network access

In case of the node not having network access, the IP address of the wan interface has to be set manually. For simplicity, the IP address of the wan interface will be set to 172.20.2.1 — the IP address of the host.

1. Connect a keyboard and a monitor to the device.
2. Power up the device once Nerve is installed.
3. Enter the login credentials for host access once the system asks for host login. The login credentials can be found in the customer profile.

4. Enter the following commands to open the wan interface configuration:

   cd /etc/network/interfaces.d
   sudo nano wan
   

5. Enter the host access password if prompted.

6. Edit the configuration the following way:

   auto wan
   iface wan inet static
     bridge_ports eth0
     address 172.20.2.1
     netmask 255.255.255.0
   

7. Enter Ctrl+S to save the configuration.

8. Enter Ctrl+X to exit the Nano editor.

9. Enter the following command to apply the changes to the wan interface by restarting the networking services:

   /etc/init.d/networking restart
   

10. Enter the host access password if prompted.

With the wan interface IP address set to 172.20.2.1 the Local UI can be reached at http://172.20.2.1:3333/.

Activating the Nerve license

After the installation, the product license needs to be activated so that Nerve can be used on the device. Connect a workstation to port LAN1 and configure the network adapter of the workstation. The IP address has to be in the same range as the IP address of the wan interface with a 255.255.255.0 subnet mask. Refer to the chapter above on how to find out this IP address.

Access the Local UI at <wanip>:3333 in a web browser and refer to License activation in the user guide for more information.

Accessing the Local UI and registering the device

With the license activated, the node needs to be registered for use in the Management System through the Local UI. To access the Local UI, first connect a workstation to port LAN1 and configure the network adapter of the workstation. The IP address has to be in the same range as the IP address of the wan interface with a 255.255.255.0 subnet mask. Refer to the chapter above on how to find out this IP address. The credentials for the Local UI found in the customer profile are also required.

1. Access the Local UI at <wanip>:3333 in a web browser.

2. Log in with the credentials from the customer profile.

   

Continue with Node configuration for information on how to start registering the device in the Management System.

Physical ports and network interfaces

Below is a depiction of the node internal networking adapted to the SuperServer E100-9AP-IA hardware. Refer to Node internal networking for more information. The table offers a quick overview of the network interfaces that can be reached through the physical ports of the SuperServer E100-9AP-IA.